Chrome-Moly Shoe for an 18" Pipe

February 22, 2002
Chrome-Moly Shoe for an 18" Pipe
Chrome-Moly Shoe for an 18" Pipe

Piping Technology & Products, Inc., designed and fabricated a Figure 700 chrome-moly shoe for an 18″ pipe used to support high temperature lines at a power plant in Mexicali, Mexico.

The shoe’s length is 12″ and the pipe centerline distance was maintained at 17 3/8″ from the bottom of the shoe. The clamp was designed at 1065°F and the load was designed for 6965 pounds. The base and clamp plates are made of A387 GR.22 plate material and the u-bolt parts are made of A193 GR.B7 bar stock.

Want to learn more about chrome-moly shoes and other products from Piping Technology and Products? Visit our webinar archives today!



access-our-webinar-archives



Read More

400 Lightweight, Vertical Constant Load Hangers

February 15, 2002
400 Lightweight, Vertical Constant Load Hangers
400 Lightweight, Vertical Constant Load Hangers
400 Lightweight, Vertical Constant Load Hangers
Constants in the Field

Piping Technology & Products, Inc. specially designed and fabricated four hundred 100-C, vertical constant load hangers for a plastics plant in Texas. The constants will be used to support a furnace standing three levels high.

In the plant, thirteen single beams confined to limited space will each hang thirty constants, therefore PT&P engineers were required to design the constants to weigh less than 150 pounds. The 136-pound constants with travels of 10 inches upward and a supporting load of 950 pounds, are 33 7/8″ in height and 8 7/8″ in width. They are also supplied with shop prime, painted finish to safeguard against the extremely hot temperatures of the furnace area. In order to insure quality and proper operations of the constants, a prototype was built and tested to MSS standards.

Need some vertical constant load hangers? Let us price one for you today!

request-a-quote


Read More

66" Diameter, Three-bolt Pipe Clamp

February 8, 2002
66" Diameter, Three-bolt Pipe Clamp
66" Diameter, Three-bolt Pipe Clamp
66" Diameter, Three-bolt Pipe Clamp
66" Diameter, Three-bolt Pipe Clamp

Piping Technology & Products, Inc. custom designed and fabricated a 66-inch diameter, three-bolt pipe clamp for a chemical company located in Deer Park, Texas.

The clamp will be used in conjunction with a PT&P Spring Hanger and a length of rod in order to support the pipeline.  After formation, the clamp’s dimensions measured at 97.75 OAL and 69.5 at its widest point. By using a FEA program, the clamp was designed for an operating load of 24,000 pounds at 500° F. The materials used consisted of 1 ¾ x 10 x 128 ¼ thick A-36 Carbon steel, with three 2½ studs and nuts.

In need of some three-bolt pipe clamps? Request for pricing today!

request-a-quote


Read More

Stainless Steel Stanchions for a Power Company

February 1, 2002
Stainless Steel Stanchions for a Power Company
Stainless Steel Stanchions for a Power Company

Piping Technology & Products, Inc. provided 35 stainless steel stanchions for pipe sizes 4 to 18 inches for a power company in Alabama.

The ends of the stanchions have shop-cut end connections that will allow field welding without any modifications by site personnel. Some stanchions were provided with straight pipe connections and others were provided with elbow connections. The minimum height requirement provided for a centerline height equal to approximately 16″ while the maximum pipe centerline was required to be at approximately 58 ½”. The stanchions were designed at 1100°F and sustained a maximum design load of 18,000 pounds. The stanchion base plates are 304 stainless steel and the tubes are constructed of A240 GR.304 seamless pipe.

Do you need stanchions for your company? Request a quote and get a response within 48 hours!

request-a-quote


Read More
Top