PT&P Roller Hangers for an Aviation Facility in California

April 2, 2018

PT&P Roller Hangers for an Aviation Facility in California

Type: Roller Hangers
Size: 12″ Wide and 15″ Tall
Material: Cast Iron & Carbon Steel
Design: 965 lbs. Operating Load & 10″ Pipe Size
Testing: Standard Quality Control

These Fig. 195 roller hangers were designed by PT&P for an aviation facility in California. They measure 12″ in width and 15″ in height. The rollers are fabricated from cast iron, with the yoke, roll rod, and hex nuts from carbon steel. The units are designed for a pipe size of 10″ and an operating load of 965 lbs. Standard quality control tests were performed prior to shipment. Roller hangers are used for the suspension of pipe from a single rod where axial movement may occur because of expansion or contraction.

Read More

Trapeze Roller Hangers for a Food Processing Facility

April 24, 2017

Trapeze Roller Hangers for a Food Processing Facility

Type: Trapeze Roller Hangers
Size: 2-5/8″ to 16-3/8″ L x 4″ to 16″ Dia. | 600 to 3,970 lb. Load
Material: Cast Iron
Testing: Standard quality control inspections

Piping Technology & Products designed these trapeze roller hangers for a food processing facility in Kentucky. These rollers range from 2-5/8″ to 16-3/8″ in length and 4″ to 16″ in diameter. They are comprised of cast iron roll and sockets, steel roll rod, continuous thread rods and hex nuts. The rollers are for pipe sizes ranging from 2″ to 16″ and load ratings from 600 to 3,970 lb. Standard quality control inspections were performed prior to shipment.

Read More

Type-C Variable Assemblies with Dual Travelers for a De-coker Unit

December 22, 2016

Type-C Variable Assemblies with Dual Travelers for a De-coker Unit

Type: Variables with dual travelers
Design: Operating load: 1,698-21,756 lbs
Material: A36 Carbon Steel with HDG finish
Size: Horizontal Travelers range from size 2 to size 4

These dual travelers with Type-C variable spring hanger assemblies were custom designed by Piping Technology & Products for valves in a de-coker unit in Texas. All completed assemblies were fabricated from A36 carbon steel with an HDG finish. The travelers range from size 2 to size 4 and are designed for 12″ of horizontal movement. The variables are designed for an operating loads ranging from 1,698-21,756 lbs.

Read More

Custom Designed Pipe Clamp and Sway Strut Assemblies for an Ethane Cracker Facility in Texas

December 12, 2016

Custom Designed Pipe Hanger and Pipe Clamp Assemblies for an Ethane Cracker Facility in Texas

Type: Pipe Clamp and Sway Strut Assemblies
Design: Operating load: 99,650 lb. | Temperature: 550°F
Material: A36 Carbon Steel
Size: Clamps: 149″ L x 14″ W x 2″ T | Load Bolt: 4-1/2″ | 68″ Dia. Pipe

Piping Technology & Products custom designed pipe clamp and sway strut assemblies assemblies for an ethane cracker facility in Texas. The clamps are designed for a 68″ diameter pipe using a bar size of 149″ long x 14″ wide x 2″ tall. The load bolt size is 4-1/2″ and the inside bolts, rods, nuts, and turnbuckle are 4″ diameter. The assemblies are completely fabricated from A36 carbon steel, and designed for an operating temperature of 550°F with a load capacity up to 99,650 lb. A visual inspection test with sample pipe and dimensional check were conducted prior to shipment.

Read More

PT&P Designed Pipe Roller Stands for a Wastewater Treatment Plant

November 7, 2016

PT&P Designed Pipe Roller Stands for a Wastewater Treatment Plant

Type: Pipe Roller Stands
Design: 1,000 lb. Load | 30″ Dia. Pipe | 18-3/4″ x 13″ x 10-3/16″ BOP
Material: Stainless Steel
Function: For support of piping that expands and contracts longitudinally and where vertical adjustment is not necessary.

Piping Technology & Products, Inc. designed pipe roller stands fabricated from stainless steel for a wastewater treatment plant. Each roller has two spring housings with eight springs in each. They are designed for an operating load of 1,000 lb. on a 30″ diameter pipeline. The rollers measure 18-3/4″ x 13″ x 10-3/16″ BOP and went through quality control inspection and tests prior to shipment.

Read More

Adjustable Pipe Stands Designed for a Crude Oil Terminal in Texas

October 24, 2016

Adjustable Pipe Stands Designed for a Crude Oil Terminal in Texas

Type: Adjustable Pipe Stands / Saddles
Design: 3″ to 25″ Dia. | +/-2″ Adjustment
Material: Carbon Steel with a HDG Finish
Function: Allow adjustment after expansion and contraction

Piping Technology & Products, Inc. designed and fabricated fifty-seven adjustable pipe stands for a Crude Oil Terminal in Texas. All the supports are fabricated from carbon steel with a hot-dipped galvanized finish. They are designed for 3″ to 25″ diameter pipelines with +/- 2″ of adjustment. Each base plate has been pre-drilled to accept anchor bolts provided at the site. The function of the pipe stand is to allow for adjustment of the support after expansion or contraction of the pipeline.

Read More

Cold Insulated Pipe Saddles with Slide Plates Designed for an Ethane Cracker at a Plant in Texas

August 29, 2016

Cold Insulated Pipe Saddles with Slide Plates Designed for an Ethane Cracker at a Plant in Texas

PT&P designed cold insulated pipe saddles with PTFE slide plates to provide sliding and guiding support for horizontal piping leading to an ethane cracker at a plant in Texas. The project fulfilled an emergency request when the client realized the product was missing at time of installation. The pipe saddles are fabricated from carbon steel with a hot-dipped galvanized finish for pipe sizes ranging from 3″ to 56″. They have a diameter of 40″, height of 23-5/8″, width of 42-1/2″ and 11-7/8″ BOP. Visual inspection and dimensional checks using a section of pipe were completed prior to shipment.

Read More

14” Diameter Pipe Clamp Assemblies Designed and Manufactured by PT&P for a Refining Project in Saudi Arabia

July 11, 2016

14” Diameter Pipe Clamp Assemblies Designed and Manufactured by PT&P for a Refining Project in Saudi Arabia

Piping Technologies & Products fabricated these special designed Split-T pipe shoes using a Figure 50 “two-bolt pipe clamp” for a refining project in Saudi Arabia.  The pipe shoes are 4″ height x 15.5″ wide x 18″ long and were fabricated from A36 carbon steel with a hot-dipped galvanized finish.  They are designed for a pipe size of 14″ with an operating temperature from -29°C to 316°C. The pipe shoes are capable of supporting an operating load of 34,000 lb.

Read More

Pipe Clamp Design, Application & Installation Webinar

June 23, 2016

This webinar is over, view the recording in webinar archives

pipe-clamp-webinar_v28This presentation will cover Pipe Clamps, including Hold-Down Clamps, Riser Clamps, Clevis Hangers, Yoke U-Bolt Clamps and Structural Supports. Learn how the appropriate type of pipe support is chosen based on the different design conditions. Find out how Finite Element Analysis is used in the design process and view the custom pipe supports designed for extreme applications.

 

Read More
Top