Piping Technology & Products Pipe Stress Solutions

PT&P was founded as a Pipe Stress company in 1975 and began doing Pipe Stress in 1973.  This was prior to the release of Caesar when most Pipe Stress Analysis was done with hand calculations.  Our ability to solve the most difficult problems led our customers to request for us to supply products as well as do Pipe Stress analysis.  Over the years, we have become better known for our manufactured products.  However, our roots in Pipe Stress Engineering are reflected in everything we do.

PT&P’s operating strategy is to provide our customers with superior value by remaining narrowly focused on Piping Systems.  As a result, PT&P’s Pipe Stress Analysis expertise is most commonly used on smaller projects or as a subcontractor to another engineering firm on a larger project.  In particular, we tend to be very cost-effective for simpler projects such as recreating the loads and movements for Spring Supports for which the original design information has been lost.

The advantages of working with PT&P for your Pipe Stress Analysis include:

  • Rapid Turnaround – PT&P can turnaround Pipe Stress Analysis in as little as 3 days
  • Cost-Effective – PT&P has a unique cost structure for small project consulting work as we have a large engineering staff of over 70 design engineers. This allows us to quickly staff a small project without worrying about staff utilization the way other firms might.
  • Small Projects – PT&P welcomes working on even the smallest of projects
  • Component Engineering Expertise – PT&P truly understands all elements of the piping system is extreme detail
  • One-Stop-Shop – PT&P can handle all aspects of the project from Pipe Stress to quoting material, to supporting on-site Installation

Examples of work we have done include:

  • Estimate Loads for 5 Springs on a Line
  • Recreate Pipe Stress Models for the key lines for the Restart of an Existing Plant
  • Conducted Pipe Stress Analysis and Design of all Pipe Supports for a Power Plant Build

Case Study: Recreating Spring Support Load and Movements

An operating plant had lost the design information for a line with 5 spring supports.  We offered them the option to estimate or to run a Pipe Stress Analysis to get exact information.  In this case, the customer decided to proceed with the stress analysis.  Figure 1 shows the output of the analysis.  As can be seen from Figure 1, we found that the unsupported span of piping was creating a moment force above maximum allowable at the nozzles.  We did not know if the original design was incorrect or if changes had been made over the years.  However, in our experience, many customers do make changes over time in their piping systems without updating the Pipe Stress Analysis.

Figure 1

 –  Pipe Stress Analysis for As-Built System

Pipe stress analysis case study 1 image1

In this case, PT&P updated the analysis with the addition of an additional Spring Support.  Figure 2 shows the updated movements of the Piping System.

Figure 2

Pipe Stress Analysis with Additional Spring Support

Pipe stress analysis case study 1 image2

Stress Analysis Projects by PT&P:

  • Olin Chemicals: Pump P-910 Suction and discharge piping spring supports bottomed out. PT&P performed the pipe stress analyses for the pump suction and discharge piping and determined the loads and movements for replacing the spring cans.
  • ExxonMobil Mont Belvieu Plastic Plant:  PT&P performed the pipe stress analyses for the pump suction and discharge piping and determined the loads and movements for replacing the spring cans.
  • Entergy/ Nisco: PT&P performed the stress analyses for the HEP systems for loads and movements to replace the existing spring supports.
  • Flint Hills Resources: PT&P performed stress analysis for cells 1 thru 4 for the FHR CCR Heater Units.
  • Vopak Terminal, Deerpark: PT&P performed stress analysis for two tanks discharge piping.
  • J&J Engineering: PT&P performed stress analyses for multiple plant piping for J&J Engineering.
  • Formosa: PT&P performed stress analysis for the sweep gas piping.
  • OCI Beaumont, LLC.: PT&P performed stress analysis for BFW piping.
  • Houston Product Company (Atlas Copco): PT&P performed stress analyses for the HSI Test Stand Piping
  • Huntsman
  • Shell Deerpark
  • Occidental Chemical Corporation
  • Portland General Electrical
  • Indianapolis Power & Light Company
  • Oxy Vinyls, LP
  • Westlake Petrochemicals, LLC
  • Tesoro
  • Ineos Styrenics
  • Valero Refining – Texas, LP
  • Rhodia, Incorporation
  • Valladolid III Energy Center
Ptp isostresssketch Ptp stresssketch

PT&P has extensive in-house finite element analysis capabilities using ProEngineer, ANSYS, and a variety of other software packages.

See this detailed analysis of a transition piece for a sample of our work.


If you have any questions about PT&P’s Pipe Stress Analysis services, please email us at shirish@pipingtech.com

Top