Tag: Big Tons

Big Ton Spring Supports Designed for a 98,250 lb. Load

December 5, 2023

Big Ton Spring Supports Designed For A 98,250 Lb. Load

Type: Big Ton Spring Supports
Size: 29″ wide x 110″ long x 35″ high
Material: HDG Carbon Steel | A193 Gr. B7 Travel Stops and Load Column
Design: 98,250 lb. | 1-3/4″ Upward
Testing: Load Cell Test

This big ton spring support assembly was designed for a facility in Kansas. For this application PTP’s big ton was used to support heat transfer and steam generating equipment typically used in fossil fuel power generation, combined cycle power generation, petrochemical, and process industries.

Big Ton spring supports are extremely stable. Base supports springs of this design are frequently used under horizontal pressure vessel saddle supports in combination with slide plates or roller supports. Our Big Ton design lends itself ideally to this support situation. Type F design is sufficient where there is a minimal amount of lateral movement, but where the combination of heavy loads and thermal expansion are required, Big Ton industrial springs should be your choice.

The big ton assemblies were fabricated from hot-dipped galvanized carbon steel and include neoprene coated springs coils. The travel stops and load column material is A193 Gr. B7. The units measure 29″ wide x 110″ long x 35″ high and are capable of supporting loads up to 98,250 lb. while accommodating movements from 1-3/4″ upward. The big tons were tested at our facility with a load cell designed by our team to ensure proper operation throughout the big ton’s operating range.

Alongside our ability to design and manufacture big tons specific to your system needs, our field service team is readily available to service, audit, maintain, and/or assist with installation of such products. For more on installation and maintenance take a look at our resource page:
big ton installation-maintenance

PT&P REF. ORIGINAL POST 07252017

Custom Designed Big Ton Spring Supports for a Propane Dehydrogenation Application in Texas

November 20, 2017

Custom Designed Big Ton Spring Supports For A Propane Dehydrogenation Application In Texas

Type: Big Ton Spring Supports
Size: 42″ x 24″ x 26 1/2″
Material: Carbon Steel
Design: 94,261 lb. Load & 0.085” Movement
Testing: Standard Load Tests

PT&P custom designed big ton spring supports for a propane dehydrogenation application at a chemical plant in Texas. The components within this assembly include the spring housing, coils, name plates, pressure plate, and load indicator. While both assemblies measure 42” L x 24” W x 26-1/2” H, it was modified based on independent specifications for operating loads and movement to accommodate a load of 94,261 lb. and 0.085” of movement. This type of support is ideal for applications, such as supporting pressure vessels that combine very heavy loads with thermal expansion because of the stability they provide. The big ton was tested in the load cell to insure proper operation throughout the entire working range of the coils.

Big Ton Spring Supports Designed for a LNG Facility in Australia

February 7, 2017

Big Ton Spring Supports Designed For A Liquid Natural Gas Facility In Australia

Type: Big Ton Spring Supports
Size: 19-5/8″ x 19-5/8″ x 15″
Material: Hot-dipped Galvanized Carbon Steel | A193 Gr. B7
Design: Movements: 3/16 ” – 1/4″ | 16,619 lb. Load
Testing: Load Cell throughout Operating Range

These big ton spring supports were designed for a liquid natural gas (LNG) plant in Australia. They were selected because the application required supporting heavy loads as the supported equipment undergoes thermal expansion during operation. The assemblies are fabricated from hot-dipped galvanized carbon steel. The travel stop rods and nuts material is A193 Gr. B7. The units measure 19-5/8″ x 19-5/8″ x 15″ and are capable of supporting loads up to 13,619 lb. while accommodating movements from 3/16″ to 1/4″. The big tons were tested with a load cell to insure proper operation throughout the big ton’s operating range.

Big Ton Spring Supports Custom Designed for an LNG Facility

September 13, 2016

Big Ton Spring Supports Custom Designed For An Lng Facility

Type: Big Ton Spring Supports with PTFE Slide Plates
Size: 29-7/8″ x 29-7/8″ 16-1/2″
Material: Carbon Steel with HDG Finish | PTFE, 25% Glass Filled Slide Plate
Testing: Tested in a press connected to the load cell

PT&P custom designed big ton spring supports with PTFE slide plates for an LNG facility in Australia. The components within the spring housing include load columns, travel stops, spring coils and lifting lugs. Each assembly is designed for an operating load ranging from 16,276 lb. to 34,479 lb. and will allow for movement between 0.16″ and 0.24″. They are fabricated from hot-dipped galvanized carbon steel and measure 29-7/8″ x 29-7/8″ x 16-1/2″. The big ton spring support is ideal for applications that have very heavy loads with thermal expansion because of the stability they provide throughout the range of travel. These supports were tested in the press connected to a load cell to insure proper operation throughout the entire working range of the coils.

Big Ton Spring Supports Designed for an LNG Facility in Australia

February 8, 2016

Big Ton Spring Supports Designed For An Lng Facility In Australia

These big ton variable spring assemblies were custom designed for an LNG plant in Western Australia. They are specially designed with PTFE, 25% glass filled slide plates, and will be used under horizontal pressure vessel saddle supports. The big tons were selected due to a combination of heavy loads and thermal expansion. The units measure 30″ x 30″ and are capable of supporting a load up to 95,000 lb. with down travel of 2 to 5mm vertical.

Big Tons with W-Beams as Stilts

September 17, 2012

105105A1

Stilts using W-Beams were added to these big ton variable assemblies in order to meet height requirements for an oil refinery in Port Arthur, TX. Entirely fabricated with carbon steel, these big tons measure 50 1/2″ – 70″ L x 18″ – 22″ W by 37″ H and are capable of supporting loads up to 113,734 lb with an upward travel range of .076″ – .816″. Permanent travel stops were later installed in order to prevent any chances of downward shift.

Big Ton Springs used in a Chemical Processing Plant

November 1, 2006
Big Ton Springs Used In A Chemical Processing Plant
Big Ton Springs used in a Chemical Processing Plant
Big Ton Springs Used In A Chemical Processing Plant
Stainless Steel Slideplates on Big Tons

The limiting constraint in designing and fabricating these big ton spring supports was to maintain an overall height less than 15-3/4″ and still allow the load table to travel downward during operation. Whereas a standard PT&P size 2-190 variable springs would have been sufficient to hold the load specified, the coil alone was taller than the space available at site. For this reason, a “big ton” design was implemented which utilized six smaller coils (2-130 size) working in parallel to produce the required load-carrying capability and spring rate.

All of the frame/housing components were made from carbon steel and supplied with an HDG finish. The travel stop rods were made of A-193 Gr. B7 material and were painted red. The slide plates sitting atop the load flange were made of polished A-304 stainless steel.

Both “big ton” assemblies are 30″ wide by 30″ deep by 15-3/4″ tall. Overall spring rate is 3,600 lb/in. and each weighed approximately 1,460 pounds. The installed (cold) load = 14,800 lbs. and the operating (hot) load = 16,075 lbs. Movement from cold to hot = 0.354″ down.

Tested in the load cell to insure proper operation throughout the entire working range of the coils, the “big tons” were then set to the cold (installed) load as specified.

Want to learn more about big ton springs? Watch one of our engineered spring webinars now!




Access-Our-Webinar-Archives



90,000 lb. Load Big Ton Springs for a Chemical Plant

April 9, 2004

90,000 Lb. Load Big Ton Springs For A Chemical Plant
90,000 lb. Load Big Ton Springs for a Chemical Plant
90,000 Lb. Load Big Ton Springs For A Chemical Plant
Name Plate Indicates Hot/Cold Loads

Piping Technology and Products, Inc. manufactured four 13,500 lb. Big Tons Springs for a chemical plant in Texas. These PTP-500 Big Ton Springs have a load capacity of 60,000 to 90,000 lb. are fabricated from A-36 carbon steel. They are designed for 750°F and a downward travel range of 3/16″ to 1/4″. These 37″ x 31″ x 30″ Big Tons will be used to support certain critical equipment with thermal expansion at the chemical plant. To assure quality, load testing was performed on the big tons prior to shipping.

Do you require big ton springs in your current or future job? Get pricing today!
Request-A-Quote

Big Ton Springs Equipped with Special Rollers

August 23, 2002
Big Ton Springs Equipped With Special Rollers
Big Ton Springs Equipped with Special Rollers
Big Ton Springs Equipped With Special Rollers
Rollers Installed On top of the Load Flanges

Piping Technology & Products, Inc. specially designed and fabricated big ton springs equipped with special rollers to accommodate moving apparatus and support piping at a refinery in India.

The specially designed big tons were made to support loads ranging from 55,000 lbs. to 114,000 lbs with no more than 5/16″ upward movement. Its composition comprises of A-36 carbon steel, built to a maximum height of 23-5/8″.

The special rollers installed on the top of the load flange, keeps the aforementioned loads moving smoothly under all kinds of conditions. To further assure their quality, each of the big ton spring assemblies underwent load testing and afterward were hot dipped galvanized to prevent against corrosion.

Want to learn more about big tons? Visit our webinar archives today!



Access-Our-Webinar-Archives

Big Ton Springs Equipped with Lifting Lugs

July 12, 2002
Big Ton Springs Equipped With Lifting Lugs
Big Ton Springs Equipped with Lifting Lugs

Piping Technology & Products, Inc. specially designed and fabricated big ton springs equipped with side lifting lugs to support piping of a 102-megawatt, refinery cogeneration power plant in California.

Under typical circumstances, this type of job application would utilize variable spring hangers, but because of the restricted space, the hangers’ size would be too small to support a hot load of 19,068 lbs and cold load of 17,212 lbs. In order to satisfy both the required loads and space, PT&P engineers designed and fabricated figure 500 big ton springs equipped with side lifting lugs. The lifting lugs were attached to allow the big ton to suspend as a variable spring would in the field.

Are big ton springs a necessity for your next project! Request a quote today!

Request-A-Quote

Big Ton Springs With Loads Up To 450,600 Newtons

November 28, 2001
Big Ton Springs With Loads Up To 450,600 Newtons
Big Ton Springs With Loads Up To 450,600 Newtons

Piping Technology & Products, Inc. specially designed and fabricated Big Ton Variable Springs for a chemical project in Canada. The supporting beams are 30″ in length with PTFE, 25% glass filled stainless steel slide plates. The Big Ton Springs were designed with six coil springs with external guides to prevent horizontal twisting and internal guides to withstand horizontal friction forces. These units were also designed for operating loads from 260,000 to 350,000 Newtons and hydro-test loads from 300,000 to 450,600 Newtons. A total of six units were painted with a special finish specified by the client.

Need a big ton? Get pricing today!

Request-A-Quote

Specially Designed 120,000 lb Load Big-Ton Spring Supports

June 8, 1994
Specially Designed 120,000 Lb Load Big-Ton Spring Supports
Specially Designed 120,000 lb Load Big-Ton Spring Supports

Pictured above are Big-Ton Spring Supports specially designed by Piping Technology & Products, Inc. These types of supports are used in supporting large and heavy units such as compressors, vessels and pumps in power and petrochemical plants. The ones below were used to support vessels in excess of 120,000 pounds. The Big-Ton Spring Support are designed to allow limited movement in confined areas. By doing this, it saves the customer from having to entirely redesign the piping system and saves thousands of dollars.

Do you need a big ton for one of your upcoming projects. Let us price one for you today!

Request-A-Quote

Webinar General

Live New Webinar

Sign-up for a Live Technical Webinar…

Piping Design Course 300Width

Online Course

Piping Design and Analysis Influence on Pipe Support Selection and Design

Surveying a piping system? Need to change a current system?

This course is also great for…

• New Engineers, Management and Operations
• Field, Process, Maintenance and New Engineers
• Piping and Piping System Designers and/or Instructors

*This online course is approved for 8 hrs. P.E. Credits

Register Now
Top