Tag: Cryogenic Pipe Supports

300+ Cryogenic Insulated Pipe Supports (Cold Shoes) for LNG Service

November 26, 2018

300+ Cryogenic Insulated Pipe Supports Designed For An Lng Pipeline

Type: Cryogenic Insulated Supports
Size: Range: 6″ to 24″ Dia. Pipe
Material: Carbon Steel | Hot-dipped Galvanized | PUF
Design: 15,000 – 30,000 lb. Load | -112 F | +/- 2″ Movement

Over 300 pre-insulated pipe supports were custom fabricated for a cryogenic pipeline at an LNG facility in Louisiana. High density polyurethane foam was used for insulation, with thicknesses ranging from 2” to 4”. The cold shoes are for pipe diameters ranging from 6” to 24” and are fabricated from carbon steel with a hot-dipped galvanized finish. They are designed for temperatures down to -112°F, movements of +/-2” and operating loads ranging from 15,000 to 30,000 lb. Standard quality control tests were performed prior to shipment.

Over 100 Cryogenic Pipe Supports Designed for a Nitrogen Facility in Colorado

September 10, 2018

Over 100 Cryogenic Pipe Supports Designed For A Nitrogen Facility In Colorado

Type: Pre-insulated Pipe Supports “Cold Shoes”
Material: CS | Red Oxide Primer | PUF Insulation
Size Range: 1/2″ – 6″ Thick Insulation | 1″ – 18″ Dia.
Design: -300°F Temperature | Lateral Restraints / Guides

PT&P custom designed more than one-hundred cryogenic pipe supports for a nitrogen facility in Colorado. The cold shoes are designed for pipe sizes ranging from 1″ to 18” diameter. They are designed with polyurethane insulation ranging from ½” to 5” thick. The clamps are carbon steel and coated with a red oxide finish. The cold shoes are designed as lateral restraints/guides that can support loads in two directions. Standard quality control tests were performed with a 6-8 week turn-around time.

Cryogenic Pipe Supports with Micarta® G-10 for an LNG Facility in Australia

April 16, 2018

Cryogenic Pipe Supports With Micarta® G-10 For An Lng Facility In Australia

Type: Cryogenic Pipe Supports
Size: Pipe Size of 1” to 36”
Material: LTCS Material Tops, Stainless Steel, & Micarta® G-10 Insulation
Design: -50°F
Testing: PMI

Piping Technology and Products supplied cryogenic pipe supports with axial stops for an LNG facility in Australia. The cold shoes were fabricated utilizing low temperature carbon steel, stainless steel and Micarta® G-10 insulation blocks. We supplied a wide range of lengths and pipe sizes from 1” to 36”. The cryogenic temperatures are low as -50°F. A special paint system was used for the low temperature carbon steel components to resist rust. PMI testing was performed on the stainless parts. Delivery was within 4-6 weeks.

Pipe Support Engineering & Design

November 27, 2017

** Turn up your speakers to hear the audio. Please be patient as the screen will become visible
shortly after the speaker begins the presentation. You may click the monitor icon below each
video to view the webinar in full-screen mode.

NOTE: PDH credits are NOT offered for our recorded webinars.

View the Slides for Above Webinar Here

PT&P’s Polyurethane Foam Machine

Check out Piping Technology & Products new polyurethane foam mixing machine. It has the ability to pour 1200 lb. of foam per minute and has the capacity to pour up to 50 cu.ft. of 20 lb. foam

Image

Pre-Insulated Pipe Supports for both Cryogenic and High Temperature Applications Webinar

October 10, 2017

** Turn up your speakers to hear the audio. Please be patient as the screen will become visible
shortly after the speaker begins the presentation. You may click the monitor icon below each
video to view the webinar in full-screen mode.

NOTE: PDH credits are NOT offered for our recorded webinars.

View the Slides for Above Webinar Here

Cryogenic Pipe Supports Designed for a Facility in Massachusetts

September 11, 2017

Cryogenic Pipe Supports Designed For A Facility In Massachusetts

Type: Cryogenic Pipe Supports
Material: Carbon Steel | Polyurethane
Design: -320°F | 36″ – 48″ Dia. | 52″ W x 57″ H x 67″ L

PT&P received an order to custom design 16 cryogenic pipe supports for a contractor in Massachusetts. They needed a pipe forming a T-section lined with insulation and trimmed to accommodate the pipe perpendicular to the shoe length. The overall dimensions of the order are pipe sizes ranging from 36″ to 48″ in diameter, 52″ width and 57″ to 67″ height. Our insulation is designed to support the pipe and its contents. When insulated pipes are supported, the weight of the pipe, the contents, the operating temperature, and the amount of energy loss must be considered. In order to support the pipe and minimize energy loss from heat transfer, a pre-insulated pipe support is necessary. If the material in the pipe is high temperature such as high pressure steam or heating oil, then high temperature insulation is required, and these supports are called hot shoes. If the material is cold, such as liquefied natural gas, cooling water or ammonia, then low temperature insulation is needed, and these types of supports are called cold shoes.

127 Cryogenic Insulated Pipe Supports Designed for a Chemical Plant

July 25, 2016

127 Cryogenic Insulated Pipe Supports Designed For A Chemical Plant

PT&P custom designed 127 cryogenic insulated pipe supports for a chemical plant in Texas. They are designed for pipe sizes ranging from 1″ – 24″ diameter and operating loads up to 120,517 lb. The insulation is high density polyurethane foam (PUF) ranging from 1″ to 7″ in thickness. The shoe and bearing plates were fabricated from carbon steel with a hot-dipped galvanized finish. The jacket was fabricated from aluminized steel and includes a vapor barrier. Standard Q.C. and dimensional tests were performed prior to shipment.

Cryogenic Pipe Supports Designed for a Hydrocarbon Production Facility

September 8, 2015

48” Dia. Cryogenic Pipe Supports Designed For A Light Hydrocarbon Production Facility

PT&P custom designed pre-insulated pipe supports with polyurethane insulation for cryogenic temperatures in a light hydrocarbon production facility in Texas. A total of 59 cold shoes were fabricated from A36 carbon steel with a hot-dipped galvanized finish. The cold shoe assemblies range in diameter from 24″-48″ and were designed to support loads ranging from 17,000 to 31,000 lb. Standard Q.C. and dimensional tests were performed prior to shipment.

30" Dia. Cryogenic Pipe Supports with PUF and Permali®Insulation for an LNG Facility

August 9, 2014

30&Quot; Dia. Cryogenic Pipe Supports With Puf And Permali®Insulation For An Lng Facility

PT&P manufactured cryogenic pipe supports for a 30″ diameter pipeline in an LNG facility located in the UAE. These cold shoe anchors prevent axial and lateral movement at temperatures down to -300°F. The bearing plate is fabricated from carbon steel and the 5″ thick insulation is a combination of high density polyurethane foam (PUF) and Permali®.

Cryogenic Insulated Pipe Supports Designed for a Natural Gas Refinery

June 23, 2013

Cryogenic Insulated Pipe Supports Designed For A Natural Gas Refinery

Over 1200 cryogenic insulated pipe supports were designed for a natural gas refinery in Abu Dhabi. The supports range from 1″ to 30″ in diameter and have 30 lb. polyurethane foam (PUF) insulation. These cold shoes are comprised of a vapor barrier, an aluminum jacket and a carbon steel base. An ice test was performed on all the supports prior to shipment.

72" Dia. Cryogenic Pipe Supports Designed for an LNG Facility

May 6, 2013

72&Quot; Dia. Cryogenic Pipe Supports Designed For An Lng Facility

Custom designed cryogenic pipe supports were fabricated for an LNG facility in Africa. The shoes range in diameter from 30″ to 72″, 45″ to 88″ in height, 42-1/2″ to 85-1/2″ in width, and 28″ to 33″ in length. The insulation is a high density polyurethane foam (PUF) ranging from 5″ to 6″ thick. The shoe and bearing plates were fabricated from carbon steel with a HDG finish. The jacket was fabricated from aluminized steel and includes a vapor barrier.

 

Cryogenic and Axial Stop Cold Shoes for an LNG Facility

November 18, 2012

8195094192 8Bff3F23Aa


Piping Technology and Products supplied these cryogenic and axial stop cold shoes for an LNG facility in Australia. A total of 28 assemblies were fabricated with carbon steel, stainless steel and Micarta® G-10 insulation blocks. They were a wide range of lengths from 24″ to 36″, widths from 6 3/4″ to 30″ and heights from 9″ to 10 1/4″. The pipe shoes will support pipes ranging in diameter from 6″ to 48″ NPS in cryogenic temperatures as low as -162°C. A special paint system was used for the carbon steel components to resist rust. PMI testing was performed on the stainless parts prior to shipping.

Insulated Pipe Supports for Temperatures as Low as -260°F for a 30" Diameter Pipe in a LNG Receiving & Regasification Plant and Refinery

January 25, 2011

Cryogenic Supports For A Lng Receiving &Amp; Regasification Plant And Refinery

These cryogenic supports (also known as cold shoes) are fabricated from 20 PCF polyurethane insulation, weigh 650 lb. each and are designed for 30″ diameter pipe. They are comprised of a carbon steel base plate and bearing plate, a vapor barrier and an aluminum jacket. The supports are designed for temperatures as low as -260°F, and measure 27″ length by 44″ height. A total of thirty-four supports were fabricated for natural gas applications, including storage and transport.

Do you see a need for cryogenic supports in your piping system? Get a quote today!

Request-A-Quote

24" Heavy Duty Cryogenic Pipe Supports

February 6, 2008
24&Quot; Heavy Duty Cryogenic Pipe Supports
24" Heavy Duty Cryogenic Pipe Supports
24&Quot; Heavy Duty Cryogenic Pipe Supports
24" Heavy Duty Cryogenic Pipe Supports

These pipe supports were designed for a petrochemical plant in Puerto Rico. The nominal pipe size of the supports ranges between 16″ and 24″. The cryogenic supports are fabricated from carbon steel and include a stainless steel jacket. They are insulated with polyurethane foam and are designed for temperatures between -270ºF and 85ºF. The load capacity ranges between 5,000 lb. and 11,900 lb.

Want to learn more about cryogenic pipe supports? Instantly view a past webinar!

Access-Our-Webinar-Archives

Cryogenic Pipe Supports for a LNG Plant in Algeria

July 2, 1993
Cryogenic Pipe Supports For A Lng Plant In Algeria
Cryogenic Pipe Supports for a LNG Plant in Algeria

The pictures above show cryogenic pipe supports designed by a Houston E&C firm for a LNG plant in Algeria. Piping Technology & Products, Inc. fabricated the these supports for a 14” pipe which operates below –50oF. Three different materials are used. The upper part which bolts to the pipe is fabricated from an alloy which retains its strength at low temperatures. The middle section is a Permali® block selected because of its strength and durability and because it is a poor conductor of heat. The bottom plate of galvanized carbon steel is bolted to the Permali® block. Permali® is a phenolic laminate made from layers of wood impregnated under vacuum with a synthetic resin. A crossed orientation of the hard wood fibers is used to provide extra strength.

Are you in need of some cryogenic pipe supports? Let us price it for you today!

Request-A-Quote

Webinar General

Live New Webinar

Sign-up for a Live Technical Webinar…

Piping Design Course 300Width

Online Course

Piping Design and Analysis Influence on Pipe Support Selection and Design

Surveying a piping system? Need to change a current system?

This course is also great for…

• New Engineers, Management and Operations
• Field, Process, Maintenance and New Engineers
• Piping and Piping System Designers and/or Instructors

*This online course is approved for 8 hrs. P.E. Credits

Register Now
Top