Blog Category: SUPPORT ASSEMBLY COMPONENTS

Adjustable Pipe Stands Designed for a Crude Oil Terminal in Texas
October 24, 2016

Adjustable Pipe Stands Designed For A Crude Oil Terminal In Texas

Type: Adjustable Pipe Stands / Saddles
Design: 3″ to 25″ Dia. | +/-2″ Adjustment
Material: Carbon Steel with a HDG Finish
Function: Allow adjustment after expansion and contraction

Piping Technology & Products, Inc. designed and fabricated fifty-seven adjustable pipe stands for a Crude Oil Terminal in Texas. All the supports are fabricated from carbon steel with a hot-dipped galvanized finish. They are designed for 3″ to 25″ diameter pipelines with +/- 2″ of adjustment. Each base plate has been pre-drilled to accept anchor bolts provided at the site. The function of the pipe stand is to allow for adjustment of the support after expansion or contraction of the pipeline.

Read More

Cold Insulated Pipe Saddles with Slide Plates Designed for an Ethane Cracker at a Plant in Texas
August 29, 2016

Cold Insulated Pipe Saddles With Slide Plates Designed For An Ethane Cracker At A Plant In Texas

PT&P designed cold insulated pipe saddles with PTFE slide plates to provide sliding and guiding support for horizontal piping leading to an ethane cracker at a plant in Texas. The project fulfilled an emergency request when the client realized the product was missing at time of installation. The pipe saddles are fabricated from carbon steel with a hot-dipped galvanized finish for pipe sizes ranging from 3″ to 56″. They have a diameter of 40″, height of 23-5/8″, width of 42-1/2″ and 11-7/8″ BOP. Visual inspection and dimensional checks using a section of pipe were completed prior to shipment.

Read More

Pipe Clamp Design, Application & Installation Webinar
June 23, 2016

This webinar is over, view the recording in webinar archives

Pipe-Clamp-Webinar_V28This presentation will cover Pipe Clamps, including Hold-Down Clamps, Riser Clamps, Clevis Hangers, Yoke U-Bolt Clamps and Structural Supports. Learn how the appropriate type of pipe support is chosen based on the different design conditions. Find out how Finite Element Analysis is used in the design process and view the custom pipe supports designed for extreme applications.

 

Read More

Over 400 Clevis Hanger Assemblies Designed for a Pulp and Paper Plant
March 28, 2016

Over 400 Clevis Hanger Assemblies Designed For A Pulp And Paper Plant

PT&P supplied over 400 clevis hanger assemblies for a pulp and paper plant in Indonesia. The assemblies accommodate elevation differences ranging from 94-1/2″ to 138″ with pipe diameters ranging from 1″ to 24″ and a rod diameter range of 3/8″ to 1-1/4″. All components were fabricated from hot-dipped galvanized carbon steel and are designed for ambient temperatures and loads ranging from 700 lb. to 7500 lb.

Read More

Roller Stands Designed for a Refinery in Mississippi
December 11, 2015

Roller Stands Designed For A 10&Quot; Dia. Pipeline At A Refinery In Mississippi

PT&P designed these roller stands for a refinery in Mississippi. The rollers were designed for ease of assembly to support a 10″ diameter pipeline. They are comprised of cast iron roll and sockets, steel roll rod, continuous thread rods and hex nuts. These rollers are designed to support a maximum load of 2,100 lb. and to allow axial movement of the pipeline.

Read More

Pipe Clamp Assemblies Custom Designed for a Synthetic Gas Plant
August 9, 2015

Pipe Clamp Assemblies Custom Designed For A Partial Oxidation Unit In A Synthetic Gas Plant

PT&P custom designed pipe clamp assemblies for a partial oxidation unit in a synthetic gas plant located in Texas. The pipe clamps were fabricated from alloy A387 and coated with a special paint for high temperatures. The assemblies were designed with supportive structures for pipe sizes ranging from 2″ to 16″. Standard quality control inspection and tests were conducted prior to shipment.

Read More

Technical Webinar: Design, Application & Installation of Pipe Clamps
August 5, 2015

This webinar is over, view the recording at: Webinars

Pipe Clamps

This presentation will cover Pipe Clamps, including Hold-Down Clamps, Riser Clamps, Clevis Hangers, Yoke U-Bolt Clamps and Structural Supports. Learn how the appropriate type of pipe support is chosen based on the different design conditions. Find out how Finite Element Analysis is used in the design process and view the custom pipe supports designed for extreme applications.

 

Read More

Stainless Steel Roller Stands Custom Designed for a Wastewater Treatment Plant
June 8, 2015

Stainless Steel Roller Stands Custom Designed For A Wastewater Treatment Plant

PT&P designed spring loaded stainless steel roller stands for a wastewater treatment plant. The rollers were custom designed for ease of assembly to support a 30″ diameter pipeline. They include eight springs in two spring housings and are designed for 1,000 lb. load. The base plate is 18-3/4″ x 13″ and the BOP is 10-3/16″. Roller stands are used to support pipelines that expand and contract longitudinally in the axial direction and where vertical adjustment is not necessary.

Read More
Top