Heavy Duty Yoke U-Bolt Pipe Clamps Designed for a Pipeline in Canada

January 24, 2015

Heavy Duty Yoke U-Bolt Pipe Clamps Designed for a Pipeline in Canada

These custom heavy duty Fig. 43 yoke u-bolt pipe clamps are designed for a pipeline in Canada. The yoke clamps are designed for 42″ diameter pipe sizes and are fabricated from hot-dipped galvanized carbon steel. They are designed to support a load of 27,500 lb. PT&P supplied a total of 28 assemblies in three weeks for this project. These yoke clamps went through finite element analysis and performance tests prior to shipment.

Read More

Adjustable Pipe Saddle Supports Designed for a Hydrocracker Project

February 9, 2014

Adjustable Pipe Saddle Supports Designed for a Hydrocracker Project

PT&P supplied sixty-nine adjustable pipe saddle supports for a hydrocracker project in an oil refinery. The supports will be installed under a trunnion and range in heights from 12″ to 48″. They have 8″ diameter top plates, and are designed to support pipes from 2″ to 8″ in diameter. The supports are fabricated from carbon steel and consist of schedule 40 and 80 pipes and concentric reducers. The operating temperature for these custom designed saddle supports is 750″F. Each assembly was inspected by Q.C. prior to shipment.

Read More

282 Instrument Supports Designed for a Six-Drum Coker Unit

October 26, 2013

282 Instrument Supports Designed for a Six-Drum Coker Unit

PT&P designed and manufactured 282 instrument supports to support a six-drum Coker unit in a refinery in Indiana. Some of the assemblies are designed to be bolted by anchor bolts while others are designed to be welded. The supports are fabricated from hot-dipped galvanized carbon steel and measure 11″ – 61″ in height and 5″ – 28″ in width.

Read More

Custom Hold-Down Pipe Clamps Designed for a Natural Gas Facility

June 10, 2013

Custom Hold-Down Pipe Clamps Designed for a Natural Gas Facility

PT&P designed custom hold-down pipe clamps for pipe sizes ranging in diameters from 6″ to 14″ at a natural gas facility. The HD-3 is an arrestor type hold down used when there is very low thermal movement and these clamps are similar to them but differ due to their adjustable bases. These clamps are fabricated from galvanized carbon steel and include a neoprene lining to absorb vibration.

Read More

30" Dia. Adjustable Pipe Saddle Supports Designed for an Oil Refinery

March 10, 2013

30" Dia. Adjustable Pipe Saddle Supports Designed for an Oil Refinery

These custom adjustable pipe saddle supports were designed for an oil refinery in Michigan. They will support 24″ and 30″ diameter pipes and range in height from 40″ to 42″. The pipe saddles can be vertically adjusted by turning the middle section of the seamless pipe and the base plates have been pre-drilled to accept anchor bolts. They are fabricated from carbon steel with a red oxide finish to protect against corrosion and were shipped within two weeks.

Read More

47 Hold-Down Pipe Clamps Designed for a Coal Fired Power Plant

February 25, 2013

47 Hold-Down Pipe Clamps Designed for a Coal Fired Power Plant

PT&P designed and fabricated forty-seven hold-down pipe clamps for a coal fired power plant in Louisiana. The hold-downs are fabricated from carbon steel and range in size from 2″ to 10″ in diameter. The HD-3 is an arrestor type hold down used when there is very low thermal movement. Its radius is lined with a belting material that is well designed to absorb shock from vibration.

Read More

36 Custom Designed Pipe Saddles for a Power Plant

September 4, 2012

Thirty-six custom designed pipe saddles were created for a power plant in Mississippi. These 20″ W x 72″ L x 30″ H saddles were made with carbon steel with PTFE slide plates. These pipe saddles were designed to support a load of 55,000 lb. and will be applied to fluid bed duct supports.

Read More

HD-2 and HD-3 Hold-down Pipe Clamps with PTFE Slide Plates

July 30, 2012

HD-2 and HD-3 Hold-down Pipe Clamps

Designed for 20″ to 30″ pipe sizes, these HD-2 and HD-3 hold-down pipe clamps were shipped to a gas pump station in South Dakota. The hold downs were fabricated from carbon steel with PTFE, 25% glass filled liners on the saddle portion and base of the pipe clamp. We fabricated a total of 22 hold down pipe clamps and shipped this rush job within one week.

Read More
Top