Blog Category: ASME/MISCELLANEOUS FABRICATION

20" Stainless Steel Suction Strainer
March 22, 2002
20&Quot; Stainless Steel Suction Strainer
20" Stainless Steel Suction Strainer

Sweco Fab, the ASME fabrication shop of Piping Technology & Products, Inc., specially designed and manufactured two 20″ OD x 36″ long, suction strainers for a chemical plant in Louisiana.

The strainers, which were fabricated from SS32, each weigh 1,300 pounds. They were designed at 300 psig and 600° F and built to ASME code. In order to insure quality of the welds, PT&P’s Q.C. inspectors 100% x-ray tested butt welds of longitudinal seams and circumference seams, head to shell. Other pressure containment welds were dye penetrant examined. The unit, as a whole, was hydrotested at 390 PSIG.

Learn more about other Sweco Fab Inc. products in our webinar archives.



Access-Our-Webinar-Archives

Read More

1,000 Standard Pipe Supports for Corrosive Environment
March 8, 2002
1,000 Standard Pipe Supports For Corrosive Environment
1,000 Standard Pipe Supports for Corrosive Environment

Piping Technology & Products, Inc., designed and fabricated over 1,000 standard pipe supports for a chemical agent disposal facility. These supports are to be used in a corrosive environment, therefore a unique, off white coating known as chemical resistant epoxy was used to cover the carbon steel, structural members.

The hardware was hot dipped galvanized, but in some cases, the u-bolts were coated with neoprene. Frames, guides, cantilever and axial stop supports comprised of the bulk of the material, however other support assembly components included rod hangers, clamped shoes and riser clamps.

Need pipe supports for your company? Get a pricing today!

Request-A-Quote

Read More

Stainless Steel Stanchions for a Power Company
February 1, 2002
Stainless Steel Stanchions For A Power Company
Stainless Steel Stanchions for a Power Company

Piping Technology & Products, Inc. provided 35 stainless steel stanchions for pipe sizes 4 to 18 inches for a power company in Alabama.

The ends of the stanchions have shop-cut end connections that will allow field welding without any modifications by site personnel. Some stanchions were provided with straight pipe connections and others were provided with elbow connections. The minimum height requirement provided for a centerline height equal to approximately 16″ while the maximum pipe centerline was required to be at approximately 58 ½”. The stanchions were designed at 1100°F and sustained a maximum design load of 18,000 pounds. The stanchion base plates are 304 stainless steel and the tubes are constructed of A240 GR.304 seamless pipe.

Do you need stanchions for your company? Request a quote and get a response within 48 hours!

Request-A-Quote

Read More

108" I.D. x 144" T-T Vessel
August 16, 2001
108&Quot; I.d. X 144&Quot; T-T Vessel
108" I.D. x 144" T-T Vessel

Sweco Fab, Inc., the ASME code fabrication shop for Piping Technology & Products, Inc., specially designed and fabricated a 108″ I.D. x 144″ T-T vessel for the Texas A&M University. The “Aggie Vessel” will be used for special research project at the university. A 24″ T-bolt closure was used for access to the vessel and two stiffner rings were installed to withstand vacuum application. Unique internal design was also applied to facilitate special equipment installation. Helium leak test at 1×10-6 cc/sec will be performed to detect leakage.

Are you in need of a vesssel? Request a quote today!

Request-A-Quote

Read More

48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels
July 6, 2001

 

48&Quot; Diameter X 96&Quot; S/S Vertical Carbon Steel Filter Vessels
48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels
48&Quot; Diameter X 96&Quot; S/S Vertical Carbon Steel Filter Vessels
Vessels

Sweco Fab, the ASME fabrication shop of Piping Technology & Products, Inc., specially designed and manufactured three steel, rubber-lined vessels for a MTBE manufacturer located in Deer Park, TX.

The carbon steel filter vessels were designed with rubber linings in order to help prevent or delay corrosion within. The vessels are 48″ diameter x 96″ s/s vertical and built to ASME. All vessels underwent hydrostatic testing in order to detect leaks (see Figure 2).

Need a vessel for an upcoming project? Get pricing today!

Request-A-Quote

Read More

16’ Dia. x 20’ Carbon Steel Storage Tank
May 11, 2001
16’ Dia. X 20’ Carbon Steel Storage Tank
16’ Dia. x 20’ Carbon Steel Storage Tank

Dual cranes are required to lift the pictured 16’ x 20’ Carbon Steel Storage Tank to a flatbed eighteen-wheeler for transportation to the paint yard.Upon completion of painting and lining it will be shipped to a major producer of caustic soda in Corpus Christi, South Texas Area.

This is one of many (similar type) tanks and pressure vessels supplied for a recent plant expansion.

Learn more about tanks and vessels from our webinar archives.




Access-Our-Webinar-Archives

Read More

ASME Catalyst Storage Bins
Asme Catalyst Storage Bins
ASME Catalyst Storage Bins

Sweco Fab, Inc., the ASME code fabrication shop of Piping Technology & Products, Inc., designed and built eleven Catalyst storage bins for a large chemical company in Geismer, Louisiana. The catalyst storage bins were fabricated from 304 stainless steel and designed for 6 psig @ 300oF.

Want to learn more about various products of Sweco Fab, Inc. Visit out website webinars today!




Access-Our-Webinar-Archives

Read More

Pig Launchers and Receivers for Separation Project
April 22, 2001

 

Pig Launchers And Receivers For Separation Project
Pig Launchers and Receivers for Separation Project

SWECO Fab, Inc. manufactured eight 8″ and four 10″ pig launchers and receivers for a separation project off the West Coast of Africa. The products were immediately put to use for placement and removal of pigs. These launchers and receivers were designed with quick opening doors and R.T.J flanges at 2300 psig, built to ASME, Sect. VIII, Div. 1 and D.N.V. inspected.

Want to learn more about pig launchers and receivers? Visit our webinar archives today!


Access-Our-Webinar-Archives

Read More

Galvanized Knee Braces
July 5, 2000
Galvanized Knee Braces
Galvanized Knee Braces

The picture above is of galvanized knee braces. Piping Technology & Products, Inc. can meet most any fabrication requirement requested in any industry, i.e. refineries, chemical plants, power plants, etc.

In need of knee braces? Let us price them for you today!

Request-A-Quote

Read More

Jack Stand
June 8, 2000
Jack Stand
Jack Stand

The photograph above shows unique jack stands designed to support stainless steel pipe. The top, which connects to the pipe at elbows, is fabricated from stainless steel. The bottom, which can be used to adjust the height, is fabricated from carbon steel and the galvanized. The two dissimilar materials are separated by a polyurethane[pdf] isolation block which is painted for protection.

Want to learn more about the other types of products we have? Visit our webinar archives today!



Access-Our-Webinar-Archives

Read More
Top