60,000 Lb. Load Type "B" Variable Spring Hangers

June 27, 2001
60,000 Lb. Load Type &Quot;B&Quot; Variable Spring Hangers
60,000 Lb. Load Type "B" Variable Spring Hangers

PT&P specially designed two Type “B” variable spring hangers (2-250-B) for an oil company in Ryazan, Russia. These variable spring hangers were custom designed to support a load of 60,000 lbs. with a spring rate of 3,648 lbs./in. respectively. Due to loading requirements, these variable spring hangers were also designed to accommodate a travel of 1″, upward movement.

Are variable spring hangers a necessity for your next project? Get pricing now!

Request-A-Quote

Read More

June 2001 News: Issue 2

June 22, 2001

Take advantage of our currently open shop space!
PT&P and its wholly owned subsidiaries US Bellows and Sweco Fab are manufacturers of a variety of high quality engineered products. We’re open, 24/7, to meet all your quick-turn/ emergency needs! PT&P and its wholly owned subsidiaries US Bellows and Sweco Fab are manufacturers of a variety of high quality engineered products.

PT&P has a system of stock inventory that allows us to quickly assemble and ship products such as:

*Engineered Spring Supports
*Expansion Joints
*Support Assembly Components
*Fabricated Pipe Shoes and Anchors
*Flow Products
*Slide Plates and more!

Read More

June 2001 News: Issue 1

June 4, 2001

PT&P Verifies New Designs for LNG Phenolic Base Support with Load Testing

Load Testing
Load Testing

Piping Technology & Products, Inc. performs thorough product testing to verify new designs to a LNG Laminated Phenolic base support for an E&C company located in Houston, Texas. In order to determine the failure loads for a 30″ diameter, pre-insulated shoes and a 6″ diameter Laminated Phenolic base support respectively, PT&P performed lateral-load and axial load tests. The load tests performed ensure the pre-insulated pipe shoes can safely sustain the specified design load. The insulated shoes tested for the E&C company will be in service in 2001 at Atlantic LNG, where they will be used to support the liquid nitrogen gas (LNG) lines.

Big Ton Springs Installation Guide
Big Ton 1. Measure the existing installed load setting height to make sure that the big ton spring will fit tightly into the space provided. Shim from below as needed to ensure proper fit.
2. Place the big ton spring in the designated location, making sure that all required slide plates, shims, or auxiliary steel are in their proper positions.
3. Travel stop bolts can be released after all testing has been done. The travel stops are painted red and located on each end of the big ton spring. Follow the steps below to release the travel bolt stops. Please refer to the drawings to the left.
(a) Turn the nut on travel stop bolt No. 1 one-half turn; repeat on bolts 2 through 4.
(b) Repeat in this sequential order until the load is released. The load has now been transferred to whatever the big ton spring is supporting.
4. CAUTION: Be sure that the nuts on the travel stop bolts are backed off enough to accommodate the appropriate travel (Example: 1 inch of travel – the nuts should be backed off by 2 inches from the bottom of the travel stop plate.)
5. At this time the Lifting Eye Bolts may be removed.

Tension Systems
In some cases, a straight line system of axial bellows anchors and guides is not practical or desired; or there is no reasonable way/ place to anchor the bellows thrust loads. In such cases self restrained bellows assemblies may be used, such as the double hinge restrained bellows shown below. Thermal expansion (or contraction) in the long pipe is absorbed by an offset deflection of the double hinge assembly. Bellows thrust load is carried by hinge bars, gimbals, tie rods or other such devices; hence normal tension is maintained in the pipe system and main anchors and full lateral restraint guides are unnecessary.

Read More
Top