Blog

Custom Big Ton Springs Designed for a 122,000 lb. Load for a Chemical Plant
May 20, 2019

Custom Big Ton Springs Designed For A 122,000 Lb. Load For A Chemical Plant

Type: Big Ton Spring Supports
Size: 52-3/4″ L x 38-3/4″ W x 91″ H
Design: 121,916 lb. Load | 3/4″ Upwards Movement
Material: HDG Carbon Steel | Neoprene Coated Springs
Testing: Load Calibration Test | Hydro-tested

PT&P custom designed a big ton spring support for a chemical plant in Pennsylvania. The big ton will be used to support a vessel in excess of 121,916 lb. and a movement of 3/4” upwards. The dimensions for this unit are 52-3/4” L x 38-3/4” W x 91” H. The big ton spring support is designed to support large and heavy units such as compressors, vessels, and pumps in power and petrochemical plants. They are designed to allow limited movement in confined areas. By doing this, it saves the customer from having to entirely redesign the piping system and saves thousands of dollars. The big ton has an internal guide and special pedestal which was designed to meet the required height of the spring and withstand the hydro-test load. A load calibration test was performed before shipping.

Read More

Variable Spring Hangers Designed for a Plant in Texas
April 22, 2019

Variable Spring Hangers Designed For A Plant In Texas

Type: B-Type Variable Spring Supports
Size: PTP 100 & 200 | 3′ – 8′ ft. Height
Design: 4,000 lb. – 17,000 lb. Loads
Material: HDG Carbon Steel | Neoprene Coated Springs
Testing: Standard Load Test | Q.C. Tests

Piping Technology and Products, Inc. recently designed and fabricated B-Type variable spring supports for a plant in Texas. The operating loads range from 4,000 lb. to 17,000 lb. The variable springs are fabricated from galvanized carbon steel, have neoprene coated steel spring coils, and are designed to operate in environments up to 750°F. They have an overall height range from 3 ft. to 8 ft″. To ensure quality, standard load tests were performed prior to shipment.

Read More

FRP Wear Pads for Corrosion Protection on Uninsulated Piping Systems
February 18, 2019

Frp Wear Pads For Corrosion Protection On Uninsulated Piping Systems

Type: FRP Wear Pads
Size: Pipe Sizes: 2″, 3″, 4″, 6″, 10″, 12″, and 16″
Length: 4″, 6″, 10″, and 12″ (can provide sizes up to 48″)
Material: Vinyl Resins
Design: Up to 400°F
Testing: Standard Visual and Dimensional Tests

PT&P fabricated 323 FRP wear pads for an oil refinery in Texas. The wear pads are for pipe sizes of 2″, 3″, 4″, 6″, 10″, 12″, and 16″, and vary in lengths of 4″, 6″, 10″, and 12″. They were fabricated from vinyl resins, and are designed for operating temperatures up to 400°F. The FRP pads are secured to the pipe using an epoxy adhesive to protect the uninsulated pipe from the metal support structure. Standard visual and dimensional tests were performed prior to shipment.

Read More

Closure Flange Support Hinges for Supporting Medium to Heavy Duty Blind Flanges
January 28, 2019
Permanent And Removable Hinges For Supporting A Medium To Heavy Duty Blind Flange
Closure Flange Support Hinges for Supporting Medium to Heavy Duty Blind Flanges

Presently, blind flanges are used to provide an airtight cover to various piping systems that include pipelines in the oil industry, heat exchangers, ships, tanks, etc.

Routine maintenance requires the heavy duty blind flange to be removed for cleaning and repairs. However, for these types of flanges, it is quite difficult to disassemble, clean and repair. It typically requires employing a forklift, crane, or other lifting devices. This can require excessive man-hours, and the alignment of the flanges can remain unpredictable.

PT&P introduced a closure flange hinge with specially designed self‐locking bolts and two self-lubricated hinge studs to support the blind flange when all the fastening bolts are removed for maintenance or replacement. The blind flange can be opened like a “door” with little effort. Our product opens up to 180 degrees, providing full accessibility to work on the pipeline, heat exchanger, or other equipment.

To solve the issues, PT&P invented two versions of closure flange hinges for blind flanges: temporary / removable hinge and permanent / fixed hinge

Portable Hinges Project Amount   Portable Hinge Close Up

PT&P recently designed 159 permanent and removable hinges for up to 72″ diameters, We can accommodate for larger sizes upon request.

View PDF Handout on Closure Flange Support Hinges

Read More

Personnel Protection Shields, Designed and Fabricated by PT&P for a Local Refinery
January 14, 2019

Personnel Protection Shields, Designed And Fabricated By Pt&Amp;P For A Local Refinery

View PDF on Personnel Protection Shields

Type: Personnel Protection Shields
Size: 11″ Dia. | Up to 48″ Lengths
Material: Carbon Steel | 2-Coat Paint System
Design: Operating Temps. Require Safeguarding Personnel

PT&P custom designed, fabricated and provided installation oversight for sixty-five personnel protection shields for a refinery in Texas. The personnel protection shields are used when insulating the line is not necessary, but operating temperatures require safeguarding personnel from coming into contact with the pipe. These shields are fabricated from carbon steel with a two-coat paint system. They are 11” diameter, and range in lengths up to 48”.

Read More

300+ Cryogenic Insulated Pipe Supports (Cold Shoes) for LNG Service
November 26, 2018

300+ Cryogenic Insulated Pipe Supports Designed For An Lng Pipeline

Type: Cryogenic Insulated Supports
Size: Range: 6″ to 24″ Dia. Pipe
Material: Carbon Steel | Hot-dipped Galvanized | PUF
Design: 15,000 – 30,000 lb. Load | -112 F | +/- 2″ Movement

Over 300 pre-insulated pipe supports were custom fabricated for a cryogenic pipeline at an LNG facility in Louisiana. High density polyurethane foam was used for insulation, with thicknesses ranging from 2” to 4”. The cold shoes are for pipe diameters ranging from 6” to 24” and are fabricated from carbon steel with a hot-dipped galvanized finish. They are designed for temperatures down to -112°F, movements of +/-2” and operating loads ranging from 15,000 to 30,000 lb. Standard quality control tests were performed prior to shipment.

Read More

Micarta Block Assemblies Designed for a Vessel Application
November 16, 2018

Micarta Block Assemblies Designed For A Vessel Application In Texas

Type: Insulated Support – Micarta® Block Assembly
Size: 2″ H x 12″ W x 81″ L
Material: Micarta® | PTFE, 25% Glass-filled
Design: -454°F | Visual / Dimensional Tests

PT&P designed Micarta® block assemblies for placement beneath the saddle support of a vessel at an oil refinery in Texas. These insulated supports measure 2” x 12” x 81” and include PTFE, 25% glass-filled material bonded to the top of the Micarta®. Micarta® consists of glass fabric with an epoxy resin, which provides great insulating characteristics and superior physical properties. The blocks are designed to prevent cryogenic temperatures down to -454°F from transferring past the base of the support to the supporting steel or foundation. Visual and dimensional tests were performed prior to shipment.

Read More

Hold-Down Pipe Clamps with Slide Plates for LNG Service
October 19, 2018

Hd-2 Hold-Down Pipe Clamps With Ptfe Slide Plates Designed For An Lng Plant In Australia

Type: Hold-Down Pipe Clamps
Size: 8″ Dia. Pipe
Material: Carbon Steel | HDG
Design: Up to 400°F Temperatures

PT&P designed and manufactured standard HD-2 hold-down pipe clamps for an LNG plant in Australia. They are fabricated from hot-dipped galvanized carbon steel and include PTFE slide plates. The hold-downs are designed for 8″ diameter pipe and an operating temperature up to 400°F. The HD-2 is a restraint type hold down which allows axial movement while restraining lateral movement.

Read More

Over 100 Cryogenic Pipe Supports Designed for a Nitrogen Facility in Colorado
September 10, 2018

Over 100 Cryogenic Pipe Supports Designed For A Nitrogen Facility In Colorado

Type: Pre-insulated Pipe Supports “Cold Shoes”
Material: CS | Red Oxide Primer | PUF Insulation
Size Range: 1/2″ – 6″ Thick Insulation | 1″ – 18″ Dia.
Design: -300°F Temperature | Lateral Restraints / Guides

PT&P custom designed more than one-hundred cryogenic pipe supports for a nitrogen facility in Colorado. The cold shoes are designed for pipe sizes ranging from 1″ to 18” diameter. They are designed with polyurethane insulation ranging from ½” to 5” thick. The clamps are carbon steel and coated with a red oxide finish. The cold shoes are designed as lateral restraints/guides that can support loads in two directions. Standard quality control tests were performed with a 6-8 week turn-around time.

Read More
Top