The picture above shows special components of today’s piping systems. At the top are two rings with machined surfaces required to help seal the system when operating at high pressures. Rings and spacers can be fabricated from a variety of metals including carbon steels, stainless steels, alloys such as Inconel®, Hastelloy or Titanium. The choice of materials depends on the temperatures and pressures the system is designed for. Holes can be drilled to produce bleed rings which relieve pressure slowly. The above picture shows orifice plates which are made from the same materials.Read More
Pictured above is one of the six identical tanks Sweco Fab, Inc. supplied for the expansion of City of Houston’s Sims Bayou Waste Treatment Plant.
These carbon steel tanks are rubber lined and have a special paint outside. Each tank has 6,000 gallon capacity.Read More
The photographs above show insulated pipe supports designed for a system being installed in a very cold climate in Russia. The insulating components are inside next to the pipe. The outside components are galvanized steel. In the foreground of the photo at the right are two fixtures which were built for load testing these pipe supports by applying known forces with a hydraulic load cell. Piping Technology & Products, Inc., fabricated prototype units for a Houston Engineering Firm and tested the units. After successful tests a number of similar units were built for shipment to Russia.Read More
The photograph above shows a launcher-receiver designed to be installed in a six inch pipe to launch and receive pipeline pigs. Pigs can be used for cleaning or for separation of two products in the same pipeline. This launcher-receiver was one of two built by the SWECO Fab, Inc. division of Piping Technology & Products, Inc. for a major Gulf Coast Refinery.Read More
The photograph above shows hydraulic snubbers which are used to protect critical components in refineries, power plants and other industrial systems from sudden movement by the attached piping system. Engineers specify these devices for systems which are subject to sudden accelerations caused by earthquakes, extreme wind loads or water hammer. The insert at the upper left shows eight snubbers, some are different sizes and six have dust covers to protect the piston seal. The snubber at the bottom has hardware attached so it is ready to be installed. Hydraulic snubbers resist sudden rapid movement of the pipe by limiting the flow rate of the fluid inside the snubber. The device is designed so slow movement, such as would be expected during thermal expansion, has practically no resistance, but sudden rapid movement is resisted with a force proportional to the velocity raised to a power, where the power is determined by the orifice valve and flow pattern in the design. Selection of materials and liquids used will depend on the environment where the snubber is installed.Read More
The above photo shows an arrestor type hold down. This type of restraint is used when there is very low thermal movement. Its radius is lined with a belting material designed to absorb shock from movement. It is widely used on compressor lines or similar applications. The restraint type hold down’s clamp radius and base is lined with PT&P’s PTFE slide plate which allows for axial movement while restraining lateral movement and used on compressor lines where temperatures are high and thermal movement is great. This anchor type hold down is utilized on pipelines and require little or no insulation. It is fabricated from carbon steel and can be used in temperatures up to 750oF.Read More
Shown above is one of three neutralization tanks engineered and fabricated by Sweco Fab, Inc. This particular tank is being shipped to the paint contractor for painting and special interior coating.
These tanks are 12 feet in diameter, 39 feet 7 inches high, and have a storage capacity of 25,000 gallons. Special features requested by the client include clips welded on the interior for mounting of headers.Read More
Piping Technology & Products, Inc. announces the latest design of their “Horizontal Upthrust” base type constant support. The table or load flange move straight up or down as the weight of the pipe is transferred to the helical coil (spring) via the internal camlinkage. PTFE, 25% glass filled, slide bearings on the four corners eliminate the possibility of binding if undue axial or lateral forces are exerted. Also, PTFE, 25% glass filled, or graphite slide bearings can be added to the table to ease movement along the axis of the pipe. The Big-Ton and Type F Base Constant Supports are still available for other applications.]Read More
Piping Technology & Products, Inc. has designed and built thirty-two constant effort supports ranging in loads from eighty to eighty-seven kips with seven and one half inches of total travel on each.Six of the thirty-two are shown in position and they will support critical portions of the heater. The balance in other parts of the plant will support equally critical lines such as main steam and boiler reheat.
Located near Calvert, Texas, this is the second generating facility for Texas – New Mexico Power at this site. Piping Technology & Products, Inc. supplied the same material on the previous installation for this client.
Learn more about our constant supports, visit the webinar archive today!Read More