Blog

Pipe Rollers for an Environmental Remediation Project
June 7, 2021

Pipe Roller Assemblies For An Environmental Remediation Project

These pipe rollers were designed for pipelines in an environmental remediation project. These rollers can also be used in conjunction with piping on bridges, landfill gas equipment, including oil-water & moisture separators, SVE systems, candlestick flares, blower packages, drainage systems, and many other infrastructure projects. The rollers are fabricated from cast iron, with a carbon steel frame, rods, and nuts. The units are designed for 14″, 18″, and 24″ pipe sizes and 5,000 to 7,200 lb. operating load. The rollers are designed to include 1-1/2″ thick insulation, and the size is selected to include the pipe covering saddle for the insulation. Standard quality control tests were performed prior to shipment. Roller hangers are used for the suspension of pipe from a single rod where axial movement may occur because of expansion or contraction.

Read More

Variable Spring Hangers Designed for a Biofuels Plant
May 25, 2021

Variable Spring Hangers Designed For A Biofuels Plant

PT&P designed and fabricated B-Type variable spring support assemblies for a biofuels plant. The variables will support pipelines that are involved in the process of converting feedstock into low-carbon synthetic crude oil. Primary biofuels are bioethanol and biodiesel. PT&P specializes in manufacturing pipe supports for high temperatures (above 750°F) applications. These variable springs will support loads up to 953 lb., insulated piping up to 1625°F, and with 1.5” upwards movement. A custom-designed 4-bolt riser clamp fabricated from A36 carbon steel for a 3” diameter pipe was also supplied for this order and used at another location in the plant. The rest of the variable spring assemblies utilized custom-designed 2-bolt pipe clamps manufactured from A240 316L stainless steel plate with A 193 GR. B8M CL.1 bolting for high temperatures. Since these variable springs were located outside the firebox and not exposed to high temperatures, they were fabricated from A36 carbon steel and hot-dipped galvanized for corrosion protection. Load and travel tests, along with Q.C. inspections were performed before shipment.

Load and travel tests, along with Q.C. inspections were performed before shipment. Biofuels are expected to double their market share by 2027. Biofuels are a subset of the new emerging demand and regulatory shift to renewables being seen in the energy sector. In addition to biofuels, other renewables include energy from solar, wind, hydroelectric, ocean, geothermal, and hydrogen sources. There has been a change in strategy for many refineries accelerated by the downturn due to COVID, to convert traditional fossil fuel refineries to renewables. With expertise and over 45 years of experience, PT&P is well-positioned to serve its customers and emerging players in the renewable energy sector. Piping Technology & Product’s specialty is the design and fabrication of products like furnace springs, constants, customized clamps, and hardware in supporting high-temperature headers and radiant coils within fired heaters.

Read More

High-Temperature Supports Designed for a Petrochemical Plant
May 3, 2021

Pipeshields Insulated Supports 138055

Pipe Shields, Inc., a division of PT&P designed pre-insulated pipe supports for a high-temperature pipeline at a petrochemical plant overseas. This style of insulated support is designed to be compact, easy to install and eliminate the need for field welding. The insulation is 5-1/2″ thick utilizing 18 lb. and 28 lb. pcf high-density calcium silicate. The “hot shoes” are fabricated from carbon steel and hot-dipped galvanized for corrosion protection. They are rated for temperatures from +40°F to +1800°F. Q.C. inspections and dimensional tests were performed before an expedited shipment.

Such insulated supports are used for chilled water, hot water, and steam line applications in industries ranging from pharmaceutical, semiconductor, paper mills, chemical plants, data centers, biofuels, and food processing to name a few. Piping Technology and Products, through its subsidiary, industry leader, and pioneer, Pipe Shields, has supplied to all these markets in the USA and internationally for over 45 years. Most recently, we made a large investment to automate manufacturing in our Houston plant to increase throughput and yield to support our customers’ needs for just-in-time deliveries reducing cash requirements on projects.

View Pipe Shields’ Model D3100 – Insulated 2-Bolt Hanger

Read More

ASME Defines Inspection Criteria for High Energy Piping
February 23, 2021

B31.1 Operations and Maintenance

According to ASME B31.1 Chapter VII Par. 140 a program shall be established for the assessment and documentation of the condition of all CPS (Covered Piping Systems) in power plants.

CPS Systems are defined in Chapter 1 Par 100.2, as systems on which condition assessments are to be conducted. This includes the following systems as a minimum.

NPS 4 and larger main steam, hot reheat steam, cold reheat steam, and boiler feedwater piping.

NPS 4 and larger systems that operate above 750°E (400°C or above 1,025 psi (7,100 kPa)

 

Other systems may be included as CPS by an Operating Company, based on their judgment. Appendix V of the code is titled ‘Recommended Practice for Operation, Maintenance, and Modification of Power Piping Systems’. This addendum is non-mandatory; however many  Power Industry operating companies’ insurance carriers are now invoking Appendix V with increasing frequency, and this is affecting the conditions of their agreements with the operating companies.

Piping Technology and Products Inc. (PT&P) has for some time been performing surveys and assessments in accordance with part H of Par. 140, which requires hot and cold walk-down readings and assessment of pipe supports, operated within the creep regime of the pipe.  These assessments are helpful in identifying, sagging lines, deformation of supports, and damage caused by upset conditions, and/or incidents, attributable to operational malfunctions, dynamic/thermal or hydraulic events.

PT&P has been performing this service for many power generation companies. Preparation of documentation, retrieval, and compilation of files for a CPS assessment, has just been completed for a major U.S power generation company. Ten large power plants were involved, and the original predominantly high-energy pipe support drawings, all engineered and designed by PT&P, were retrieved from PT&P archives dating back ten years.

We will be happy to answer any of your technical questions about our survey capabilities, as well as any other engineering or field services that your organization may need.

If you need assistance, we are available 24×7 for emergencies or reach our field service team directly.

 

Read More

High-Temperature Pre-Insulated Pipe Supports Designed for 42″ Dia. Pipelines
February 2, 2021

High-Temperature Pre-Insulated Pipe Supports Designed For 42&Quot; Dia. Pipelines

Pre-Insulated pipe supports were designed for high-temperature service at an oil refinery for a client that specializes in the engineering and design of fired heaters, furnaces, pre-heaters, and heat recovery systems. These high-temperature pipe supports were fabricated from carbon steel and designed for pipe sizes ranging in 36” – 42” diameter and are not only used for new construction but also upgrades and revamps. The “hot shoes” were designed with the addition of “Spring Washers” (not shown here) to maintain consistent clamping force when the pipe expands and contracts. The insulation is 3″ thick and comprised of High-density Calcium Silicate (asbestos-free) structural inserts treated with water repellant. Standard quality tests were performed before shipment. Our hot shoes are used extensively in Refineries, Styrene Plants, Hydrogen Plants, LNG Facilities, Semiconductor Fabrication Facilities, and General Building Construction.

Read More

Constant Spring Supports for a Leading Energy Transportation and Midstream Service Provider
October 27, 2020

Constant Spring Supports Custom-Designed For A Leading Energy Transportation And Midstream Service Provider

PT&P custom-designed constant spring support assemblies for an energy facility in Canada. These 100–E Type (layout B) constants were supplied with an extended hanger rod and fabricated from A36 carbon steel with 5160 alloy steel coil springs. They are designed for an operating load from 2,370 lb. to 9,240 lb., and movements from 1-1/2” to 8-1/4”. The dimensions are 12” W x12” L x 30” H and 14” W x 19” L x 53” H. Load and travel tests along with a quality control inspection were conducted prior to shipment.

Read More

U-Type Constant Spring Supports with Stainless Steel Slide Plates
September 30, 2020

 U-Type Constant Spring Supports With Stainless Steel Slide Plates

PT&P custom-designed U-type constant spring supports for an oil refinery in Texas. Constants can be utilized in refineries within blocks such as hydrogenation units, naphtha desulfurization units, and fluid catalytic crackers. The spring’s frame is manufactured from A36 carbon steel and hot-dipped galvanized to protect against corrosion. For instances where there was axial and lateral movement, 240 Gr. 304 slide plates were installed on the load flanges of the constants. The constants supplied are designed for an operating load ranging from 1,085 lb. up to 17,480 lb. and horizontal travel from 2.5” to 6”. The overall dimensions range in size from 17” H x 20” W x 31” L to 28” H x 26” W x 66” L. Load and travel tests per industry standards were performed prior to shipment.

Read More

PT&P Designed and Fabricated Variable Springs for a Refinery in Texas City
July 20, 2020

Pt&Amp;P Designed And Fabricated Hanger And Base-Type Variable Springs, Constant Spring Supports, And Sway Struts For A Refinery In Texas City

Type: G-Type Variable Spring Support Assemblies
Design: Operating Loads from 3000 lb. to 4000 lb.
Movement of 1”
Material: Carbon Steel
Testing: Load & Travel Test |  Q.C. Inspection

Pictured here is a Type G variable spring hanger assembly designed for an operating load up to 4000 lb. and 1” movement. This type of support assembly is formed by welding two standard spring assemblies to the ends of a pair of channels. The Type G assembly is especially adaptable for avoiding interference in spaces where the headroom is limited. The assemblies are fabricated from carbon steel and underwent spring load tests before shipment.

Read More

Constant Spring Supports Designed for LNG Service in Louisiana
July 7, 2020

Constant Spring Supports Designed For Lng Service In Louisiana

Type: B-Type Constant Spring Supports
Size: 11-5/8 W x 41” L x 19” H to 21” W x 88” L x 38” H
Material: A36 Carbon Steel | Hot-dipped Galvanized
Design: Operating Load Range: 3,170 lb. to 48,400 lb.
Movement of 3” to 8”
Testing: Q.C. Inspection | Load and Travel Tests

PT&P manufactured B-type constant spring supports for LNG service in Louisiana. These constants are fabricated from A36 carbon steel with alloy steel 5160 spring coils. The constants are designed for an operating load range of 3,170 lb. to 48,400 lb., and movements from 3” to 8”. They range in size from 11-5/8 W x 41” L x 19” H to 21” W x 88” L x 38” H. To avoid delivery delay, a standard frame was paired with an oversized coil and coil housing. The lugs were rotated 90 degrees from the standard to allow the hanger to swing beyond +/- 4” of side-to-side swing. Standard load and travel tests were performed prior to shipment.

Read More

6-1/2 Foot Diameter Custom Insulated Sliding Pipe Shoes for HVAC Service at a Semiconductor Manufacturing Facility
June 8, 2020

6-1/2 Foot Diameter Custom Insulated Sliding Pipe Shoes For Hvac Service In Oregon

Type: Insulated Sliding Pipe Shoes
Size: 78″ NPS | 12″ L x 90″ H x 85″ D
Material: HDG Carbon Steel | High-Density Calcium Silicate
Design: +/- 3″ Axial & +/- 1″ Lateral Movements
Operating Loads up to 88,000 lb.
200°F Temperature Pipeline
Testing: Q.C. Inspection | Visual & “Fit-Up” Tests

PT&P custom designed insulated sliding pipe shoes for HVAC service at a semiconductor manufacturing facility. The shoes are fabricated from A36 carbon steel and hot-dipped galvanized for corrosion resistance, and include insulating material consisting of high-density calcium silicate. The insulated sliding shoes are designed for a 78″ pipe size with overall dimensions of 12” L x 90” H x 85” D to accommodate +/- 3″ axial and +/- 1 lateral movement at a pipeline temperature of 200°F. This design can accommodate operating loads of 88,000 lb. with each shoe weighing approximately 1,200 lb. Our quality control department performed visual and “fit-up” tests for this “Rush” shipment. *image shows product during assembly

Read More
Top